Your Plumbing Crash Course: A Guide to Installing a Bathtub
Your Plumbing Crash Course: A Guide to Installing a Bathtub
Blog Article
They are making a number of good pointers about A Step-by-Step Guide to Installing a Bathtub as a whole in this post following next.
Mounting a tub isn't specifically rocket science, but it does require strong plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old tub with a new one is likewise a moderately difficult task. If the old bathtub is easily easily accessible, the project can relocate speedily; if you have to open a wall surface to eliminate the old bathtub and place the new tub, the job is a lot harder. In either case, the job is within a home handyman's abilities, although you will need a helper to vacate the old tub and also embeded in the brand-new one. Ensure you have actually certified yourself for the work and are comfortable attempting it. Rather than working with a specialist to take control of a halfway-completed project, it is better to think about employing one prior to you start. Possibilities are you may need an expert plumber to make tube links.
This write-up will certainly help you mount a brand-new bathtub in your shower room if you have already bought a new bathtub and also don't require to alter the plan of your previous water supply pipelines.
Your tools and also material checklist need to consist of the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your setup, then the first thing you should do is disconnect the supply of water. After doing so, activate the taps to drain any water continuing to be in the system. The process of getting rid of the existing faucets can be quite troublesome due to the restricted access that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been removed, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing substance.
Prior to carrying on to fit the new taps, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end supplies a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin making sure that the washers remain in place in between the tap as well as the sink. Safeguard the tap in position with the maker provided backnut. When the tap is firmly in place, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular faucet connectors. The former kind ought to be linked to the faucet ends first, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Setting up the Tub
Using both wood boards under its feet, position the bathtub in the required position. The wood boards are helpful in equally spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 small points.
The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the level and also changing the feet on the bathtub until the spirit level checks out level.
To install faucets, fit all-time low of the furthest versatile tap connector to the proper supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Turn on the water system as well as check all joints and brand-new pipework for leaks as well as tighten them if required. Load the bathtub as well as additionally inspect the overflow electrical outlet and the normal outlet for leakages.
Finally, repair the bath paneling as defined in the maker's instruction manual. Tiling and sealing around the bath tub needs to wait till the bathtub has been used a minimum of when as this will settle it into its final position.
Preparing for the Setup
To start with, the sustaining framework supplied with the bath needs to be fitted (if required) according to the supplier's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to make sure that if the faucet comes with a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the flexible faucet ports to the bottom of both faucets utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you make use of every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath must currently be ready to be suited its last position.
Tiling Around the Tub
In the area where the bathroom fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, creating the water to permeate the wall in between the bath and the tiling, leading to complications with moisture and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures as well as installations. They are offered in tubes as well as cartridges, as well as can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Remember to always fill the bathtub with water before securing, to allow for the motion experienced when the tub is in use. The sealant can fracture fairly early if you do not take into account this activity prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the market. It is advisable to fit the floor tiles using waterproof or waterproof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been introduced to that report on A Step-by-Step Guide to Installing a Bathtub through someone on a different web address. Those who liked our page kindly make sure you remember to share it. I am grateful for your time. Come back soon.
Schedule A Service Call Report this page